how to clean a vent a hood fan

Hood Cleaning - Premier Magic trick Lung®

For your kitchen ventilation to work in good order, it is important to clean the cetacean mammal housing or filters regularly. Please review the procedure for ad hoc your pattern. Vent-A-Hood® Range Hoods will be equipped with the Magic Lung® blower system, the Power Lung™ K-Series blower arrangement (V-Line and ARS Duct Free) remote cetacean system RM1000/RM1500, or Budget Line (M Series) M600/M1200 interior cetacean system. This page is for the Deceptio Lung® blower.

Tough Cleaning Models with the Magic Lung®

Incision A - Hood Canopy

Wipe down the interior and exterior of the hood as needed with a soft cloth and warm soapy water (liquid dish detergent is accepted). Do not utilise acids, abrasives, b detergents, solvents, or scouring pads. Stainless steel should cost treated with a quality stainless cleaner so much as Stainless Nerve Magic® (Vent-A-Hood® part number SS64). Follow altogether label instructions. Do not polish crossways the grain operating room in a circle.

Real copper, real brass, and hammered copper hoods will oxidize and/or tarnish over time. Use a quality copper operating room governance cleaner much as Red Bear Copper Polish (Vent-A-Hood part number CP101). Follow all label instructions. Make not polish across the grain or in circles. Do not consumption acids, abrasives, b detergents, degreasers, solvents, or scouring pads.

Section B - Blower Unit

WARNING: To decoct the jeopardy of physical harm, be bound the blower is turned off in the hood before removing the shield(s) and blower living accommodations(s).

The Venthole-A-Hood® Magic Lung® blower captures grease by-products in the cetacean housing(s) and E-Z Clean electric fan shield(s). E-Z Clean blower shields command more frequent cleanup than the cetacean mammal housing but individual cooking habits determine how often each item will need to equal cleaned. Stinky fat content foods and heavy cooking may require cleaning after each use.

E-Z Clean blower shields are easily removed for cleaning by pulling the E-Z Sporting blower shield(s) toward the front of the hood being protective to keep the tray level if the hood has been recently used.

To remove the blower trapping(s) and damper(s), first remove the E-Z Clean blower shield. The cetacean housing is removed for cleaning by unsnapping the suitcase latches (one happening each side of the housing). And so, pull the trapping forward and softly "crown" it downwards to clear the cetacean wheel(s). The blower wheel(s) can be removed (if necessary) by using the hex wrench that was furnished this manual. Look part C of this section for details connected how to washed the blower wheel(s).

Clean the shield(s), damper(s), and/or blower housing(s) in a go down of warmly soapy pee (liquid dish detergent) and let soak for a few minutes. Wash with a sponge surgery dishcloth, wash and let run out ahead reinstalling. Alternatively, the electric fan housing(s) and E-Z Clean blower shield(s) may beryllium placed into a dishwasher.

Section C - Blower Wheel

WARNING: To reduce the adventure of personal injury, be sure the blower is turned sour in the hood before removing the blower shell(s) and blower living accommodations(s).

Regular cleaning of the blower housing should prevent grease accumulation along the blower wheel. If dirt work up should pass off, the blower wheel may easily be cleaned in aim using a soft bristle soup-strainer and a common degreaser such every bit Formula 409®. Mind not to move OR lose the metal reconciliation clips that may personify affixed to the wheel (C).

In instances where the blower wheel Crataegus oxycantha call for to be far, follow the instructions below.

Removing the blower roulette wheel requires a 1/8" hex wrench. A T-grip hex wrench (A) is available from Vent-A-Punk® to accomplish this (Part # AW101). There is a small down screw on the side of the hub of the wheel (B) that tightens up against a "flat" spot on the efferent ray of light. The mark screw must be rotated ½ turn contraclockwise to polish of the blower cycle. Insert wrench through and through the blades of the cetacean mammal wheel and into the set screw. If the roll is sticky to withdraw, the area where the centrifugal shaft makes middleman with the blower wheel hub may involve to be sprayed with common penetrating oil much as WD-40®.

After allowing the penetrating oil colour to soak for a couple of minutes, push the blower wheel frontwards slightly, then gently pull the blower wheel off the motor gibe. Use caution to avoid bending or distorting the blower wheel and take care not to move or lose the metal balancing clips that may be affixed to the wheel (C).

A soft bristle toothbrush with loving saponaceous pee may be used to clean the blades, or sop the blower wheel in fresh soapy water. When reinstalling the cycle onto the motor shaft, make sure the set have it away makes direct contact with the "flavorless dapple" on the motorial calamus. Slide the blower wheel onto the motor shaft as Interahamw as it bequeath go, making sure the back of the cetacean wheel does not touch the motor mount screws sticking from the causative.

If the blower wheel is too far back, it will rub the motor mount screws, and if it is too far forward, it will rub the inside of the blower housing. Adjust the blower steering wheel slimly to receive the correct front to rise location. Tighten the ordered screw (clockwise) to lock the blower wheel in the correct position.

NOTE: For hoods that have more than one blower wheel, make sure that white blower wheels are matched up with white motive rings, and black blower wheels are paired dormie with dishonourable motor rings. The hood will not perform properly if blower wheels and motors are mismatched.